Technology of laying gypsum tiles with your hands

Gypsum tiles have to be laid correctly, as not only the aesthetic appearance of cosmetic facing, but in addition the service

quality of this material will rely on the engineering of work. The product is also universal, and it may be attached to concrete,

plaster, brick or gypsum board sheets, provided that the top layer of the base is even and has no defects.

In the event the flaws of the base are important, it should be completely treated with primer, and then a cement mortar is made,

which matches all of the cracks. Subsequently the surface ought to be repeatedly primed and dried. Primer treatment is essential

to improve the bond between the tile and the wall. In cases like this, its makeup should choose a special, containing elements

which stop the appearance of fungus and mold.

In the modern interior of the rooms most often used gypsum tiles, even imitating natural brick or stone. To perform cosmetic

finishing your self, it’s necessary firstly to pick a scheme of tile placement and prepare a remedy. It’s crucial to look closely

at the opposite side of the substance. If its surface includes an embossed surface, then the glue ought to be placed using an

trowel, also if it’s even, then with a notched one.

The technologies of the job is as follows:

* A thin layer of glue mortar is placed on the pre-prepared wall. It’s distributed over the bottom so that it is likely to place

4-5 tiles. Decorative cladding may be placed both on plasterboard, and on putty.

* Cover the rear side of the tiles with glue.

* Plaster components are pushed against the walls and their location is corrected. To align the seams, it’s suggested to use


* Finishing is carried out in rows, all which ought to be changed by half a tile. Facing is carried out into the corners of the

space, then immediately remove any remaining mortar at the joints.

Drying the walls takes no longer than a day and needs a constant humidity and temperature within the room. The last point in the

laying of gypsum tiles is the decoration. To do this, the joints between the components are full of a special solution, the color

of which suits the brick.

Decorative imitation of brickwork on the walls will be completed in the following ways:

* Cutting on the plastered surface of the stitches of masonry with a bolt cutter along with your hands;

* laying of tiles beneath the brick:

* imitating the format and color of the side of one brick;

* Imitating a fragment of brickwork of several bricks.

The best approach to decorate »beneath the brick » is the one which enables you to make a practical coating with the maximum look of

its similarity to natural masonry. All 3 approaches to execute this kind of finishing functions meet the needs, but the cutting

edge of joints with a bolt is more labor-intensive along with the creation of large quantities of dust, so let us consider more

common manners.

The old finish is removed from the walls, and also the surface, if necessary, is leveled to eliminate the requirement to paste

plaster onto a thick layer of adhesive.

Combining such cladding with different types of interior finishes can be both systematic and performed with no clear consistency,

chaotically, together with imitation of indications of aging.

With the help of cosmetic gypsum tiles it is possible to mimic a lot of textures.

A large number of textures can be imitated with the support of decorative gypsum tiles.

The wall where it’s to be set up should have the following attributes:

* Hardness and intensity of the outside;

* The absence of uneven locations and sharp sections;

* not any deformations.

Cosmetic tiles in the interior of the kitchen

Walls are made from a variety of substances, so let’s break down the principles of installment.

When dealing with concrete, there’ll be no huge problems. It is only required to take into consideration the porosity of the

material. Concrete, which has practically no pronounced pores, ought to be treated with a good primer.

Mounting gypsum tiles concrete

Before beginning work on the installation of gypsum tiles to the walls, it is worth assessing the strength of this surface. When

the plaster does not drop off the walls and at the identical time holds nicely, it is possible to simply paint it with primer.

Mount the tiles onto the painted concrete shouldn’t. The surface ought to be scratched, making sure to misfire, then it should be

grouted and covered with a coating of plaster.